|
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3291 2017ASTM F3291-17Withdrawn Standard: Standard Test Method for Measuring the Force-Resistance of a Membrane Force Sensor (Withdrawn 2023)ASTM F3291Scope 1.1 This test method covers the force versus resistance measurement of a membrane force sensor (MFS) where the electrical resistance decreases as the force on the sensor is increased. 1.2 An MFS may or may not be electrically open in its static state. This depends on the attributes required for the application. If the MFS has a measureable resistance in static state, it was most likely designed to be used as a variable resistor, not as a normally open switch. A high but measurable resistance, in static state, may still be considered an open switch if the resistance is above the closed resistance threshold recognized by the interface electronics. 1.3 Special printed conductive polymer inks or characteristics, or both, of the sensor design are used in MFS to achieve variable resistance when compressed. As force is applied to the MFS the resistance continues to decrease, but not linearly, until a point where additional force does not change the resistance appreciably. Ideally, when force is removed from the MFS the resistance will return to, or close to, its original value. 1.4 Materials other than conductive polymers can be used in an MFS and also exhibit reduced resistance with increasing force. 1.5 This test method should not be confused with Test Method F2592 for measuring the force-displacement characteristics of a membrane switch (MS) that is designed for momentary closure. Although the resistance of a MS does change during contact closure the change from high resistance to contact resistance is very sudden and additional force does not have a significant effect on the resistance; that is, an MS is not designed to be used as a variable resistor. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords force-sensitive resistor; force sensor; FSR; membrane sensor; membrane switch; pressure sensor; resistive sensor; ICS Code ICS Number Code 31.220.01 (Electromechanical components in general) DOI: 10.1520/F3291-17 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|