|
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8661 2026ASTM D8661-26e1Active Standard: Standard Test Method for Determination of Lead in New Enamel Paint Samples through X-Ray Fluorescence (XRF) AnalysisASTM D8661Scope 1.1 This test method covers a procedure specified for the analysis of new enamel paint samples for the determination of lead (Pb) in the concentration range of 50 ppm to 300 ppm using the standardization of an X-ray fluorescence (XRF) analyzer against inductively coupled plasma-optical emission spectroscopy (ICP-OES). This test method does not address the use and performance of ICP-OES for the analysis of Pb in paint, nor does it cover the generation of the ICP-OES versus XRF correlation. 1.2 This test method should be used by analysts experienced in the use of XRF, the interpretation of spectral and matrix interferences, and procedures for their correction. 1.3 In this test method, specific methods are cited for preparing test solutions of dried, homogenized new enamel paint samples for analysis. 1.4 It is the user’s responsibility to ensure the validity of this test method for sampling materials of untested matrices. 1.5 No detailed operating instructions are provided because of differences among various makes and models of suitable XRF analyzers. Instead, the analyst shall follow the instructions provided by the manufacturer of the particular instrument. 1.6 In this test method, comparative accuracy of different devices or the precision between instruments of the same make and model are not addressed. 1.7 In this test method, there are notes that are explanatory and are not part of the mandatory requirements of this test method. 1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords lead; new enamel paint analysis; standardization of XRF using ICP-OES; XRF analysis; ICS Code ICS Number Code 71.040.50 (Physicochemical methods of analysis) DOI: 10.1520/D8661-26E01 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|