|
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-A582 2012ASTM A582 / A582M - 12e1Standard Specification for Free-Machining Stainless Steel BarsActive Standard ASTM A582 / A582M | Developed by Subcommittee: A01.17 Book of Standards Volume: 01.03 ASTM A582 / A582MAbstract This specification covers hot-finished or cold-finished bars, except bars for forging, suitable for machining processes. It includes rounds, squares, and hexagons in the more commonly used types of stainless free-machining steels designed especially for optimum machinability and for general corrosion and high-temperature service. Bars may be furnished either hot finished or cold finished in one of the conditions specified. Materials shall adhere to specified chemical composition requirements. At least one hardness testing shall be made midway between surface and center on each lot to determine that the material conforms to hardness requirements. Also, test methods and definition for hardness testing are presented. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers hot-finished or cold-finished bars, except bars for forging ( Note 1 ), suitable for machining processes. It includes rounds, squares, and hexagons in the more commonly used types of stainless free-machining steels designed especially for optimum machinability and for general corrosion and high-temperature service. Stainless steel bars other than the free-machining types are covered in a separate specification ( Note 2 ). 1.2 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard: within the text and tables, the SI units are shown in [brackets]. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
Note 1 For bars for reforging, see Specification A314 .
Note 2 For non-free machining stainless bars, see Specification A276 .
ASTM Standards A276 Specification for Stainless Steel Bars and Shapes A314 Specification for Stainless Steel Billets and Bars for Forging A370 Test Methods and Definitions for Mechanical Testing of Steel Products A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products A959 Guide for Specifying Harmonized Standard Grade Compositions for Wrought Stainless Steels E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) Keywords austenitic stainless steel; ferritic stainless steel; free-machining stainless steel; martensitic stainless steel; stainless steel bars; ICS Code ICS Number Code 77.140.60 (Steel bars and rods) DOI: 10.1520/A0582_A0582M-12E01 ASTM International is a member of CrossRef. ASTM A582 / A582MThis book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|