Abstract

This specification covers cast alloy steels in the normalized and tempered or quenched and tempered condition, suitable for high strain gradient conditions. One test block for each heat is required. The test block configuration and size are specified. Tension and Charpy impact tests and oxygen, nitrogen, and hydrogen gas content tests shall be performed. The steel shall be made by electric furnace process with methods, such as argon-oxygen-decarburization, to conform to the maximum gas level. Heat treatment procedure shall be done. Multiple austenitizing and tempering are permitted. The chemistry grade shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, and aluminum. Residual elements include: zirconium, copper, titanium, tungsten, vanadium, columbium, and boron. A product analysis shall be made for specification conformance. Casting shell and core depth zone shall be established and examined. Repair methods such as grinding and welding are detailed.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers cast alloy steels in the normalized and tempered or quenched and tempered condition, in section sizes through 37 in. (940 mm), suitable for high strain gradient conditions such as those encountered in hooks, shackles, support frames, and other lifting devices. The classes of steel in this specification are weldable only with qualified procedures.

1.2 Section range and class selection will depend on design and service conditions. Users should note that this specification contemplates mechanical property gradients.

1.3 The values stated in inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in non-conformities with the specification. Inch-pound units are applicable for material ordered to this Specification and SI units for material ordered to this Specification.

1.4 If, by agreement, castings are to be supplied in a partially completed condition, that is, all of the provisions of the product specification have not been filled, then the material marking (see Section 15) and certification (see Section 14) are to reflect the extent to which the product specification requirements have been met.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A370 Test Methods and Definitions for Mechanical Testing of Steel Products

A609/A609M Practice for Castings, Carbon, Low-Alloy, and Martensitic Stainless Steel, Ultrasonic Examination Thereof

A703/A703M Specification for Steel Castings, General Requirements, for Pressure-Containing Parts

E94 Guide for Radiographic Examination

E165 Practice for Liquid Penetrant Examination for General Industry

E709 Guide for Magnetic Particle Testing

E1019 Test Methods for Determination of Carbon, Sulfur, Nitrogen, and Oxygen in Steel, Iron, Nickel, and Cobalt Alloys by Various Combustion and Fusion Techniques

E1447 Test Method for Determination of Hydrogen in Titanium and Titanium Alloys by Inert Gas Fusion Thermal Conductivity/Infrared Detection Method

E1806 Practice for Sampling Steel and Iron for Determination of Chemical Composition

Manufacturers Standardization of the Value and Fittings Industry Standards

Keywords

aluminum nitride; AOD; heavy section; hydrogen gas; nitrogen gas; oxygen gas; Aluminum nitride; AOD (argon-oxygen-decarburization); Heavy steel materials/applications; High-strength steel castings--specifications; Hydrogen gas; Nitrogen gas; Oxygen gas; Steel castings--specifications;

ICS Code

ICS Number Code 77.140.80 (Iron and steel castings)

DOI: 10.1520/A1001-01R10

ASTM International is a member of CrossRef.

ASTM A1001