Already a subscriber? 
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN 60384-6:2005 Fixed capacitors for use in electronic equipment - Sectional specification. Fixed metallized polycarbonate film dielectric d.c. capacitors, 2006
- Word file - copy.pdf [Go to Page]
- 1 General [Go to Page]
- 1.1 Scope
- 1.2 Normative references
- 1.3 Information to be given in a detail specification [Go to Page]
- 1.3.1 Outline drawing and dimensions [Go to Page]
- 1.3.1.1 Mounting
- 1.3.2 Ratings and characteristics [Go to Page]
- 1.3.2.1 Rated capacitance range
- 1.3.2.2 Particular characteristics
- 1.3.2.3 Soldering
- 1.3.3 Marking
- 1.4 Terms and definitions
- 1.5 Marking
- 2 Preferred ratings and characteristics [Go to Page]
- 2.1 Preferred characteristics [Go to Page]
- 2.1.1 Preferred climatic categories
- 2.2 Preferred values of ratings [Go to Page]
- 2.2.1 Rated capacitance (CR)
- 2.2.2 Tolerance on rated capacitance
- 2.2.3 Rated voltage (UR)
- 2.2.4 Category voltage (UC)
- 2.2.5 Rated temperature
- 3 Quality assessment procedures [Go to Page]
- 3.1 Primary stage of manufacture
- 3.2 Structurally similar components
- 3.3 Certified records of released lots
- 3.4 Qualification approval [Go to Page]
- 3.4.1 Qualification approval on the basis of the fixed sample size procedure [Go to Page]
- 3.4.1.1 Sampling
- 3.4.2 Tests
- 3.5 Quality conformance inspection [Go to Page]
- 3.5.1 Formation of inspection lots
- 3.5.2 Test schedule
- 3.5.3 Delayed delivery
- 3.5.4 Assessment levels
- 4 Test and measurement procedures [Go to Page]
- 4.1 Visual examination and check of dimensions
- 4.2 Electrical tests [Go to Page]
- 4.2.1 Voltage proof [Go to Page]
- 4.2.1.1 Test circuit
- 4.2.2 Capacitance
- 4.2.3 Tangent of loss angle (tan () [Go to Page]
- 4.2.3.1 Measuring conditions for measurements at 1 000 Hz
- 4.2.3.2 Requirements for measurements at 1 000 Hz
- 4.2.3.3 Measuring conditions for measurements at 10 kHz
- 4.2.4 Insulation resistance
- 4.2.5 Characteristics depending on temperature (if required by the detail specification)
- 4.3 Robustness of terminations [Go to Page]
- 4.3.1 Initial measurements
- 4.4 Resistance to soldering heat [Go to Page]
- 4.4.1 Conditions
- 4.4.2 Final inspection, measurements and requirements
- 4.5 Solderability [Go to Page]
- 4.5.1 Test conditions
- 4.6 Rapid change of temperature [Go to Page]
- 4.6.1 Initial measurements
- 4.7 Vibration [Go to Page]
- 4.7.1 Final inspection, measurements and requirements
- 4.8 Bump [Go to Page]
- 4.8.1 Initial measurements
- 4.8.2 The detail specification shall state which of the following severities applies.
- 4.8.3 Final inspection, measurements and requirements
- 4.9 Shock [Go to Page]
- 4.9.1 Initial measurements
- 4.9.2
- 4.9.3 Final inspection, measurements and requirements
- 4.10 Climatic sequence [Go to Page]
- 4.10.1 Initial measurements
- 4.10.2 Dry heat
- 4.10.3 Damp heat, cyclic, Test Db, first cycle
- 4.10.4 Cold
- 4.10.5 Low air pressure
- 4.10.6 Damp heat, cyclic, Test Db, remaining cycles [Go to Page]
- 4.10.6.1 Final inspection, measurements and requirements
- 4.11 Damp heat, steady state [Go to Page]
- 4.11.1 Initial measurements
- 4.12 Endurance [Go to Page]
- 4.12.1 Initial measurements
- 4.12.2
- 4.13 Charge and discharge [Go to Page]
- 4.13.1 Initial measurements
- 4.13.2 Final measurements and requirements
- 4.14 Component solvent resistance
- 4.15 Solvent resistance of the marking [Go to Page]
